How to Change a Toilet Flush
|

How to Change a Toilet Flush?


One kind of plumbing problem of a toilet which doesn’t flush and it occurs to maximum toilets. Fortunately, there are straight solutions where you can perform yourself to be aware of the toilet working anew. That means replacing or fixing your toilet flush, still, you don’t know how to overcome the problem.

Now, we will discuss the three samples of the toilet flush accessible to you while purchasing and how they vary from each other.

Toilet flush problem: sometimes, your toilet cannot flush thoroughly for various reasons. When water comes the bowl but doesn’t drain appropriately once flush due to the blockage.

Though, if in the toilet bowl water retains its normal level, and water doesn’t run down from your cistern, in that time problem remains in the cistern flush technology.

You may face the following issues:

  • Imperfect flushing apparatus
  • Fewer water levels in your tank or cistern
  • Crushed toilet handle
  • Inaccurately connected the flush link

Forms Of Toilet Flush Control


Typically three types of toilet flush controls involve conventional handle/lever up to buttons. The three main principal control types are:

Conventional lever: It is the foremost toilet flushing control type that doesn’t grant any control over the extent you can flush.

Single push-down button: It is extra modern than the traditional lever type but the flushing volume the same.

Double push-down button: This control type conserves water by delivering a choice between a full flush and a partial flush. In this control, the smaller button generally releases around ½ the volume that flushed by the larger control button.

Also check: Compact corner toilet

A toilet flushes handle changing procedure:

Transferring The Old Handle


  • Primarily you require to obdurate your toilet’s water supply and take aside the cistern lid. The valve restrains the water supply and is adjusted to the pipe or wall back to the toilet. Switch the valve clockwise to shut off the water supply. To avoid damage just keep the cistern lid on a toilet.
  • Then, you have to drain the cistern. And if your water supply is switched off, normally flush the water outside or extract the toilet flapper to flow out the water.
  • When the cistern is drained unfix the chain adjusted to the handle.
  • If it is unchanged, you should remove the placing nut which retains the handle in the proper place. Unscrew the nut and the black o-ring and slide it down the lever to gather in it.
  • Next, pull the used handle out from your toilet via the hole, as the handle is separated from the chain.

Also check: Sink on top of toilet cistern

Setting The New Handle


  • During unpack-age it you should inspect for damage and then haul the placing nut and o-ring from your new handle. The o-ring (rubber) will meantime be jointed to it, unscrew the installing nut by turning it clockwise.
  • Go on the lever into your toilet cistern, the opposite of how you adopted the old one off with leading it through the hole for the handle towards the chain clip.
  • Keep the placing nut and o-ring behind and screw them in place. Firstly conduct the o-ring onto the lever. After doing a similar task by the setting nut until it retains the o-ring in place.
  • Join the chain to the lever around 2.5 cm or an inch of loose of a few holes. To get proper flush you must leave this suitable slack.
  • Switch the water supply behind the valve and check the new toilet flush handle. Test whether the handle can move easily. If the toilet runs properly, set the lid back on.

Rules To Replace A Toilet Button Flush


In this process, you need to turn your water supply off, and then empty the cistern of water.

  • At first, to move the cistern lid you should unscrew the toilet flush button as well as unscrew your toilet shut-off valve.
  • Now remove the cistern and then unscrew the wing nuts under the pan which maintains the cistern in place. Flow out the remaining water and eliminate the watertight rubber seal set from the toilet bowl to the cistern.
  • You can unscrew also your old button flush mechanism to remove it by hand. To loosen it applies the pliers for tightening.
  • Next, screw it in the appropriate place and tighten it with your hand where no need for any pliers.
  • Set the new watertight seal in the cistern and your toilet pan after that just refit the cistern. It should be centred completely.
  • Set aside the mechanism by containing the back nut and unscrew it so carefully.
  • Rejoin the water supply to your cistern, and then turn on the water. Test the leaks and check the button flush unit.

Also check:

Last Updated on January 1, 2022

Similar Posts